1. Trademarks and copyright

PIC and PICmicro are registered trademarks of Arizona

Microchip Inc. E-blocks is a trademark of Matrix

Technology Solutions Ltd.

2. Disclaimer

The information provided within this document is

correct at the time of going to press. Matrix TSL reserves

the right to change specifications from TSL to time.

3. Testing this product

It is advisable to test the product upon receiving it to

ensure it works correctly. Matrix provides test procedures

for all E-blocks, which can be found in the Support

section of the website.

4. Product support

If you require support for this product then please

visit the Matrix website, which contains many learning

resources for the E-blocks series. On our website you will

find:

• How to get started with E-blocks - if you are new to

E-blocks and wish to learn how to use them from the

beginning there are resources available to help.

• Relevant software and hardware that allow you to use

your E-blocks product better.

• Example files and programs.

• Ways to get technical support for your product, either

via the forums or by contacting us directly

General information

The EB006 V9 PICmicro microcontroller programmer

connects to your PC via USB to provide you with a low

cost and flexible PICmicro microcontroller programmer.

This board can be used with conventional microcontroller

programs that generate hex code for the PIC family:

MPLAB, C compilers, BASIC compilers etc. The EB006

V9 has many features that are optimised for use with

Flowcode version 6 including Ghost technology.

The board will program most 8, 14, 18, 20, 28 and 40 pin

flash PICmicro microcontroller devices using the free

‘mLoader’ programming software provided. mLoader

can be downloaded from the Matrix web site.

The board also provides ‘clean’ access to all Input/Output

lines on the relevant PICmicro microcontroller device.

These are presented on 9 way D-type connectors: 8 bits

and earth. A range of additional E-blocks boards can

plug into these D-type connectors to provide a rapid

prototyping system for learning and development.

More information on Ghost technology can be found on

our website at www.matrixtsl.com/ghost.

1. Features

• E-blocks compatible

• Low cost

• Used as a programmer and as a development board

• Programs a wide range of PICmicro MCU devices

• Full suite of programming software available

• Ghost technology included

• Removable crystal oscillator source

• 5 I/O ports

• In-Circuit Debugging via PICkit2 connector

• In-Circuit Debug with Flowcode 6

• In-Circuit Test with Flowcode 6

• Charge pump capability to allow high voltage

programming from USB supply

• 2mm power connector sockets

• Powerful 16bit host chip with Ghost technology

operating system included

• All pins on target device monitored by host

microcontroller

• On-board SRAM memory for data storage

• LEDs for Power, In-Circuit -Debug, In-Circuit -Test,

and Program

• Lower operating voltage (9V)

Circuit description

The multiprogrammer solution is made up of two

parts: a circuit board that allows various slave PICmicro

devices to be programmed, and the Windows based

programming utility ‘mLoader’.

1. Power supply

The board is normally operated from a regulated DC

supply of 7.5 - 9V or from a USB supply. This allows full

operation including programming. The board can be

operated solely from the USB cable provided. However

care must be taken, as there is only limited power that

can be taken from a computer’s USB port.

The jumper link system, J11, allows the user to decide

on the source of the power supply. If using a regulated

7.5V power supply the jumper should be positioned to

the right hand side of the jumper system labeled ‘PSU’. If

using USB power place the jumper on the left hand side

of the jumper system. LED D6 indicates that power is

correctly supplied t

参考价格：35.2844

型号：PIC16F777-E/P 品牌：Microchip 说明：PIC16F777-E/P多少钱，2026年最近一个月行情走势，PIC16F777-E/P批发/采购报价，PIC16F777-E/P行情走势销售排行榜，PIC16F777-E/P报价。